top of page

Leak Detection for Power Generation Condensers

Ninety percent of the power plants in the United States are fueled by coal, nuclear materials, natural gas, and oil.


Leak Detection Applications


These thermoelectric plants use the different types of fuel to boil water and create steam, which turns the turbines to generate the electricity. Once the steam has passed through the turbine, it must be cooled back into water for reuse by the condenser. The exhaust steam from the turbine is condensed back into water by transferring the heat to the condenser coolant, typically cold water. A common condenser is the surface condenser, also called a water-cooled shell and tube heat exchanger.


A secondary function of the condenser is to maximize turbine efficiency by maintaining a proper vacuum. Decreasing the operating pressure of the condenser (i.e. increasing the vacuum) therefore, increases the electric output of the turbine by increasing the enthalpy drop1 of the expanding steam. Operating the condenser at the highest vacuum increases plant efficiency allowing the plant to produce more electricity.


When a vacuum leak occurs in the condenser, non-condensable gases are introduced that must be vented. The gases increase the operating pressure, thereby reducing the turbine output and efficiency. The gases also decrease the heat transfer of the steam to the coolant and can cause corrosion in the generator.


Current Test Methods


Several methods for leak testing are used in the power plant, but the most common method is Helium Leak Testing. For vacuum testing, a high vacuum pump and backing pump is used to evacuate the system of most gases. This creates the right condition for a mass spectrometer. Gases are ionized and accelerated through a magnetic field in the mass spectrometer, which isolates gas molecules by mass. This separation allows for the extremely small amounts of Helium to be detected. Helium is introduced to the condenser system by spraying around the vacuum portions of the condenser. The mass spectrometers placed at the gas outlet of the extractor or at other sites within the vacuum region of the condenser. For pressure testing, Helium is introduced into the system and a sniffer probe is used on the outside to detect escaping Helium gas.


Helium Leak Testing offers several advantages including sensitivity (10-5 to 10-7 cc/sec), leak rate measurement, ability to seal leaks as soon as identified, and leak test during normal plant operation. However, there are several disadvantages to Helium Leak Testing:


  • The results are operator dependent.

  • Equipment needs to be calibrated frequently.

  • The mass spectrometer is easily damaged in caustic environments.

  • Use of one or more pumps, along with the mass spectrometer or sniffer may require two persons.

  • Multiple leaks can be masked by one another if they are too close together.

  • The Helium may be blocked internally by a membrane or leak through an open valve before reaching the sniffer.




Ultrasound: An Alternative Test Method


Due to technological improvements, ultrasound detection has become an alternative approach for vacuum leak detection. As tested and used by NASA on the International Space Station2 , ultrasound detection technology is now capable to detect all turbulent flow gas and vacuum leaks. Ultrasound is used by many power plants for condenser leak detection.


In China’s power plants, for example, ultrasound was tested through a three-year pilot program for its performance to find condenser leaks, thereby improving plant efficiency and power generation output. Twenty-five percent of the Chinese power plants participated in the test with favorable results. The decision was made to institute a permanent program with the opportunity for all of the Chinese power plants to participate going forward.


An ultrasound detector works by detecting ultrasound produced by the turbulent flow of a pressure or vacuum leak. As a gas or liquid escapes from one higher pressure system to the lower pressure side, the molecules become agitated.


The turbulence produces sound pressure variations at frequencies all along the spectrum from about 20 Hz up to 100 kHz. The amplitude or intensity of the sound at the source of the leak is dependent upon a number of factors including pressure differential, directional radiation pattern, humidity, temperature, and the physical characteristics of the crack.


The ultrasound detector uses a transducer that is most sensitive to pressure changes around 40 kHz. The detected ultrasound is converted into the audible range of hearing (nominally 20 Hz – 20 kHz) and output to a headset. The converted, amplified, filtered sound of the leak can be distinctly heard by a technician. Any sounds outside of 40 kHz produced by the manufacturing environment or power generation plant are inherently ignored by the ultrasound detector. Leaks can, therefore, be easily located in any noisy environment.


Other advantages of ultrasound for leak detection include the following:

  • Ease-of-use – simply adjust the sensitivity on a small, handheld receiver up or down to locate and pinpoint the leak; quickly scan areas from distances up to 300 feet

  • Directionality – due to low amplitudes and short wavelengths, ultrasound travels in linear paths and does not tend to travel around corners or reflect; leaks are not easily masked

  • No calibration – ultrasound is used for indication and location, not measurement of leaks. The detectors are ruggedized for use in the most caustic of environments including power plants

  • Sensitivity – improvements to the technology have given the capability to find leaks faster and with greater confidence in order for condenser systems to run at normal and even improved vacuum levels to improve power turbine efficiency

  • Costs – the cost of the high end ultrasound detector required for condenser leak detection is three to five times less than the cost of a Helium leak detection system, requires less training, and is much faster to use. In many power plants where ultrasound is deployed, a technician is used full time to scan the condenser, exchanger, and multiple other systems for ultrasound. A 0.01% improvement in power generation pays for the integration and manpower of the technology in a matter of days.

80 views0 comments

Recent Posts

See All

Commenti


bottom of page